CVE Database

In the Linux kernel, the following vulnerability has been resolved: spi: Fix DMA mapping ownership on partial map failure If RX mapping fails after TX mapping succeeds, __spi_map_msg() unmaps TX but leaves tx_sg_mapped set. If TX mapping fails on a later transfer, mappings created for earlier transfers remain active. In both cases, cur_{tx,rx}_dma_dev have not yet been updated because they are assigned only after every transfer has been mapped. The subsequent spi_unmap_msg() may therefore unmap the TX mapping again or release earlier mappings using a NULL or stale device. Using a NULL device can trigger an oops. An empty SG table does not prevent the NULL dereference because dma_unmap_sg_attrs() accesses the device before checking the entry count. Publish both mapping devices before mapping starts and unwind all failures through __spi_unmap_msg(). This clears the mapping flags and releases each mapping once with the device that created it. Publishing the devices before the loop also refreshes them when no transfer needs mapping. No mapping flag is set in that case, so current users do not use the pointers as mapping owners.

In the Linux kernel, the following vulnerability has been resolved: scsi: target: iscsi: Reserve a terminator byte for the login payload iscsi_target_check_login_request() rejects a login PDU whose DataSegmentLength exceeds MAX_KEY_VALUE_PAIRS, but the test is '>' and login->req_buf is allocated with exactly MAX_KEY_VALUE_PAIRS bytes. Since iscsit_get_login_rx() receives payload_length + padding bytes, where padding = ((-payload_length) & 3); any payload_length from 8189 to 8192 fills the whole 8192 byte buffer. The write stays in bounds, but no byte is left for a NUL terminator. The buffer is subsequently consumed as a C string. In the CHAP path chap_check_algorithm() calls kstrdup(a_str), and extract_param() calls strstr(in_buf, pattern) followed by strlen_semi(), none of which take a length. convert_null_to_semi() additionally rewrites every embedded NUL to ';', so even a payload made of well formed NUL separated key=value records is left without a terminator. These walk past the end of the object into adjacent slab memory. It is reachable by an unauthenticated initiator against a portal configured for CHAP; when authentication is not required iscsi_login_zero_tsih_s2() rewrites AuthMethod to None and the CHAP path is never entered. Allocate one extra byte. kzalloc() zeroes it and nothing ever writes to it, as every writer copies to offset 0 for at most MAX_KEY_VALUE_PAIRS bytes, so the buffer is always terminated.

In the Linux kernel, the following vulnerability has been resolved: ceph: lock mutex in ceph_mds_check_access() MDS session OPEN handling replaces mdsc->s_cap_auths under mdsc->mutex, freeing the previous array and its strings. ceph_mds_check_access() traverses this array without holding the mutex. A concurrent session reopen can therefore free the array while it is being inspected, resulting in a use-after-free like this: Unable to handle kernel paging request at virtual address 003aaad64b2c8bb9 [...] Internal error: Oops: 0000000096000004 [#1] SMP Modules linked in: CPU: 56 UID: 2953037534 PID: 1253231 Comm: php-cgi8.4 Not tainted 6.18.45-i2-ampere #1146 NONE [..] pc : ceph_mds_check_access+0xd4/0x550 lr : ceph_mds_check_access+0xc8/0x550 [...] Call trace: ceph_mds_check_access+0xd4/0x550 (P) ceph_atomic_open+0x138/0xbe8 path_openat+0xa24/0xfa8 do_filp_open+0x94/0x158 do_sys_openat2+0x88/0xf8

In the Linux kernel, the following vulnerability has been resolved: nvme: add missing SRCU grace period in error path nvme_alloc_ns() error path at out_unlink_ns removes ns from the namespace head siblings list with list_del_rcu(&ns->siblings) but does not wait for SRCU readers before freeing the namespace struct. Multipath code iterates the head->list under srcu_read_lock() in nvme_find_path() and nvme_mpath_revalidate_paths(), so a concurrent reader can still hold a reference to ns when kfree(ns) runs. The normal removal path in nvme_ns_remove() correctly calls synchronize_srcu(&ns->head->srcu) after list_del_rcu() to wait for in-progress readers. Add the same grace period in the error path.

In the Linux kernel, the following vulnerability has been resolved: nvmet-auth: Synchronize timeout work during SQ teardown nvmet_auth_sq_free() cancels auth_expired_work with cancel_delayed_work(). If the work has already started, cancellation does not wait for the callback. Transport teardown can consequently free or reuse the queue containing struct nvmet_sq while nvmet_auth_expired_work() still accesses that SQ. Add a teardown-specific helper that synchronously drains the delayed work before freeing authentication state, and use it from nvmet_sq_destroy(). Keep the non-synchronous helper for in-band authentication state cleanup, where the SQ owner remains alive.

In the Linux kernel, the following vulnerability has been resolved: nvmet-tcp: fix out-of-bounds write when receiving an over-long PDU nvmet_tcp_try_recv_pdu() reads a PDU header into the fixed 128-byte queue->pdu union, then computes the remaining payload length as queue->left = hdr->hlen - queue->offset + hdgst; and reads that many more bytes into &queue->pdu + queue->offset, without ever bounding the result against sizeof(queue->pdu). A struct nvme_tcp_icreq_pdu is itself 128 bytes, exactly the size of the union. Once a header digest has been negotiated (hdgst = 4), a second ICReq passes the hlen == nvmet_tcp_pdu_size() check but yields queue->left = 128 - 8 + 4 = 124, so bytes 8..132 are written into the 128-byte buffer -- 4 bytes past its end, over queue->hdr_digest and queue->data_digest. Those bytes are attacker-controlled (an ICReq carries no digest), and the duplicate ICReq is only rejected later, after the overflow. A remote unauthenticated host can thus corrupt kernel memory adjacent to the receive buffer. Reject any PDU whose declared length would read past the end of queue->pdu before the second recv.

In the Linux kernel, the following vulnerability has been resolved: KVM: nVMX: Service local TLB flushes on failed nested VM-Enter KVM services local TLB flushes on "full" nested VM-Exits (through __nested_vmx_vmexit()), but not if a nested VM-Enter fails (e.g. due to failed VMCS checks in nested_vmx_enter_non_root_mode()). However, it is possible that KVM had queued TLB flushes that need to be performed, even if the nested VM-Enter was not successful. For example, if VPID is disabled for L2 (via nested_vmx_transition_tlb_flush(), or if via the MSR load lists, as the SDM says: If any MSR is being loaded in such a way that would architecturally require a TLB flush, the TLBs are updated so that, after VM entry, the logical processor will not use any translations that were cached before the transition. The SDM is unclear about when the TLB flush should occur, and whether or not a failed VM entry would flush the TLB, so it is safer to always do the TLB flush in this case. More concretely, KVM also updates the last VPID L1 used for L2 in nested_vmx_transition_tlb_flush() (i.e. last_vpid), even if the VM entry ultimately fails. With the current code, KVM could miss a TLB flush if L1 changes L2's VPID, then does a failed VM entry followed by a successful one, as the failed VM entry would update last_vpid but not actually flush the TLB. Servicing local TLB flushes on failed VM entries makes sure that the TLB is always flushed when last_vpid is updated.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Correctly handle end of VA space TLBI invalidation Our TLB invalidation by VA code is based on comparing two ranges, one defined by the TLB, and one defined by the TLBI instruction. Each range is defined by a start and a size. However, the way the comparison is done doesn't account for address rollover, as it compares an address with (base + size). This works nicely until this expression represent the last page/block in the TTBR1 VA space, as the result is a big fat 0. And a failed TLB invalidation. Rewrite the comparison in a way that is immune to the address rollover (making the end address inclusive instead of exclusive), and move this into a common helper that is used by both VA and IPA invalidations, as suggested by Hyunwoo Kim (although the IPA version didn't suffer from this particular problem, obviously).

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Make VNCR invalidation participate in MMU invalidation retry A VNCR TLB invalidation can occur on one vcpu while another vcpu is faulting in this same page. Without correctly handling this, we can end up with the following scenario: - vcpu A walks the PTs to translate VNCR - before vcpu A is able to grab the MMU lock to insert the TLB, vcpu B updates the S1 PTs with an invalid entry, and issues a TLBI S1E2 for this VA - vcpu A inserts the TLB for something that is now invalid This isn't a new problem, and we manage S2 by having the MMU notifier to bump up mmu_invalidate_seq on invalidation so that the fault can be replayed. We can perform something similar here, and extend invalidate_vncr_va() to update the same counter, clearly indicating that the context has changed under our feet. This is safe as the invalidation always happen while holding the MMU lock for write, and that we sample the sequence number before walking S1.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Remove VM-wide VNCR mapping counter The global VNCR mapping counter is used to decide whether an L1 provided VNCR page is mapped in L0 on any CPU at the point of dealing with a TLB invalidation. It is incremented when a mapping is made in the fixmap, and decremented when unmapped. As it turns out, this tracking has several flaws: - we are trying to invalidate TLBs, and the mapping is only an opportunistic consequence of the TLB. Checking this counter to decide whether a TLB needs to be invalidated may result in missed invalidations. - an L1 vcpu invalidating its own TLB (a very likely case) will not succeed in invalidating the VNCR pseudo TLB because that page is not mapped in L0 at this stage. Given that this tracking fails at delivering the minimum guarantees that are required and is only a performance optimisation, remove it completely.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Sign-extend VA for range-based TLBI invalidation When the decode_range_tlbi() helper was moved to be used for S1 TLBIs, the required sign extension was omitted. Add it. As a result, special care must be taken to not overflow PA bits when this is used for S2 invalidation.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Hold qpair lock when sending NVMe LS reject qla_nvme_ls_reject_iocb() allocates from and advances the request ring through __qla2x00_alloc_iocbs() (which assumes the hardware_lock is held) and qla2x00_start_iocbs() (which advances the ring and rings the request-in doorbell), but takes no lock itself. Two of its callers invoke it without the producer lock held: - qla_nvme_xmt_ls_rsp(), the NVMe-FC .xmt_ls_rsp transport callback, on its error path, and - qla2xxx_process_purls_pkt(), run from the purex work/DPC context. Both use ha->base_qpair, whose qp_lock_ptr is hardware_lock, so they can run concurrently with normal I/O submission on the base ring and corrupt the ring producer state, leading to duplicated or dropped commands. The third caller, qla2xxx_process_purls_iocb(), runs inside qla24xx_process_response_queue() with the qpair lock already held and is safe; that is also why the lock cannot be taken inside the helper itself (it would recursively re-acquire hardware_lock on the response path). Take qp_lock_ptr around the two unlocked callers and document the helper as caller-locked. Both run in process context, so spin_lock_irqsave() is used and nothing in the locked region sleeps.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Avoid double completion in async IOCB timeout qla2x00_async_iocb_timeout() tries to abort a timed-out async IOCB. When qla24xx_async_abort_cmd() fails, both the SRB_LOGIN_CMD path and the SRB_CTRL_VP/default path scan outstanding_cmds[] for the SRB and then call sp->done(sp, QLA_FUNCTION_TIMEOUT) unconditionally, without checking whether the SRB was actually found and removed. If the response ISR completes the same handle first, it removes the SRB under qp_lock_ptr and runs sp->done() -> complete(sp->comp). The submitter qla24xx_control_vp() wakes from wait_for_completion(), clears sp->comp, drops its reference and returns, reclaiming the on-stack completion. The timer reference keeps the SRB alive across the timeout handler, but not the submitter's stack. The timeout then issues a second sp->done() -> qla_ctrlvp_sp_done(), which evaluates "if (sp->comp) complete(sp->comp)"; with the pointer loaded before the submitter's NULL store, complete() writes into the freed stack frame, a use-after-free. Track whether this path removed the SRB from outstanding_cmds and only call sp->done() when it did, so the command is completed exactly once by whichever path owns it. This mirrors the sp_found guard already used in qla24xx_abort_iocb_timeout().

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Bound rsp_info_len to avoid OOB sense-data read In qla2x00_status_entry(), the FWI2 status path advances sense_data and shrinks par_sense_len by rsp_info_len: if (IS_FWI2_CAPABLE(ha)) { sense_data += rsp_info_len; par_sense_len -= rsp_info_len; } rsp_info_len is a 32-bit value taken directly from the target's FCP response (sf.rsp_data_len), while par_sense_len is the IOCB data area size (28 bytes for 24xx, 60 bytes for 29xx). A hostile or buggy target reporting an rsp_info_len larger than par_sense_len makes the unsigned subtraction underflow to a huge value and advances sense_data out of bounds. The underflowed par_sense_len then defeats the cap in qla2x00_handle_sense(): if (sense_len > par_sense_len) sense_len = par_sense_len; memcpy(cp->sense_buffer, sense_data, sense_len); so the memcpy reads up to SCSI_SENSE_BUFFERSIZE bytes from the out-of-bounds sense_data pointer, leaking adjacent response-ring/heap memory into the command's sense buffer. Clamp rsp_info_len to par_sense_len before the subtraction so par_sense_len can never underflow and sense_data stays within the IOCB data area. The fix sits before the comp_status switch, covering both qla2x00_handle_sense() call sites.

An unauthenticated actor with network access to the private HA interconnect may trigger sensitive HA peer functions without verification. This could result in elevated command execution on Edge units where HA is enabled.

Apache Airflow Keycloak provider: the unauthenticated token endpoint accepts a client-credentials grant for any confidential client registered in the Keycloak realm, not only the client configured for Airflow. No allowlist restricts which client ids may authenticate, so the credentials of an unrelated application that happens to share the realm are valid Airflow login credentials, and Airflow mints a signed session token for that application's service account. The endpoint also answers unauthenticated credential guesses against Keycloak under Airflow's identity. Affects deployments using the Keycloak auth manager whose realm is shared with other confidential clients. The attacker needs valid credentials for any one of those clients, not for Airflow. Resource authorization is still evaluated per subject, so the access gained is whatever that service account holds, plus any endpoint gated only on being authenticated. Users of apache-airflow-providers-keycloak are recommended to upgrade to version 0.10.0 or later, which accepts only the configured client on that grant.

Apache Airflow Keycloak provider: from Airflow 3.3 the Keycloak auth manager takes a user's identity from the signed Airflow session token but takes the Keycloak access and refresh tokens used for every authorization decision from separate, unauthenticated cookies, and never checks that the two describe the same subject. A user who holds any valid Airflow login of their own, together with another subject's Keycloak access or refresh token obtained out of band, can pair the two: Airflow then authorizes requests with the foreign token's privileges while the session identity, audit log and cache keys continue to name the attacker's own account. The refresh path re-issues an Airflow session token for the original identity carrying the foreign tokens, so the mismatched pairing survives across sessions. Affects deployments running Airflow 3.3 or later with the Keycloak auth manager. Earlier versions carried the Keycloak tokens inside the signed session token, so the binding existed and was lost when they moved into separate cookies. Users of apache-airflow-providers-keycloak are recommended to upgrade to version 0.10.0 or later, which binds the cookie-supplied tokens to the session identity.

An unauthenticated P4Runtime (Programming Protocol-Independent Packet Processors Runtime) client can achieve arbitrary code execution under certain conditions on affected platforms running Arista EOS configured with P4Runtime. P4Runtime is disabled by default in Arista EOS. By crafting a malicious packet during the initiation of a P4Runtime session, an attacker can obtain complete administrative control over the compromised switch. This issue was discovered internally by Arista, and the company is not aware of any malicious exploitation of this vulnerability in customer networks.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix tree connection use-after-free in smb2_tree_connect() ksmbd_tree_conn_connect() publishes a new tree connection in sess->tree_conns with a single reference and returns its pointer to smb2_tree_connect(). The handler continues to initialize the object and build the response after publication. A concurrent session logoff can erase the connection and drop that reference, freeing the object while the handler still uses it. BUG: KASAN: slab-use-after-free in smb2_tree_connect+0xe3d/0xf90 smb2_tree_connect (fs/smb/server/smb2pdu.c:2872) handle_ksmbd_work process_one_work worker_thread kthread After xa_store() succeeds, take a second reference before releasing tree_conns_lock. The original reference belongs to the xarray entry and the second belongs to the creating smb2_tree_connect() handler. Keep the references balanced in every path: - On normal exit or an error after publication, smb2_tree_connect() drops its creator reference. Error cleanup also calls ksmbd_tree_conn_disconnect(), which drops the xarray reference only if it removes the exact entry. - SMB2 TREE_DISCONNECT uses the same helper to remove the entry and drop its xarray reference. The request's existing lookup reference remains owned by the request and is released by the existing cleanup. - Session LOGOFF removes each entry and drops its xarray reference. If it wins the race, later cleanup sees that the entry is gone and does not drop that reference again. To enforce this ownership, claim the disconnected state and erase the exact entry atomically under tree_conns_lock. This guarantees one drop for the xarray reference and one drop by each in-flight user, regardless of which teardown path wins. If logoff removes the entry before initialization completes, fail the connect instead of marking the detached object TREE_CONNECTED.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix out-of-bounds read in ext4_read_inline_dir() ext4_read_inline_dir() can read a dirent header past the end of its inline buffer, triggering a slab-out-of-bounds read during getdents64(): BUG: KASAN: slab-out-of-bounds in __ext4_check_dir_entry Read of size 2 at addr ffff88800f3dd23c by task exploit/148 ... __ext4_check_dir_entry ext4_read_inline_dir iterate_dir The dirent payload lives in a buffer of exactly inline_size bytes: dir_buf = kmalloc(inline_size, GFP_NOFS); but iteration runs in a position space extra_offset bytes larger (extra_size = extra_offset + inline_size) so the synthetic "." and ".." land at their block-dir offsets. A dirent is formed at "dir_buf + pos - extra_offset", yet the ext4_check_dir_entry() length argument uses the larger extra_size. A position whose dirent header would extend past extra_size is therefore accepted, and the rescan loop's rec_len probe and ext4_check_dir_entry() dereference de->rec_len before the entry is rejected. Reject a position whose minimum-size dirent header would not fit within extra_size before forming de, in both the rescan and main loops, and pass inline_size rather than extra_size to ext4_check_dir_entry() so the length check matches the physical buffer.

In the Linux kernel, the following vulnerability has been resolved: xfrm6: fix out-of-bounds write in xfrm6_input_addr() when secpath is full The depth check in xfrm6_input_addr() is off by one: if (1 + sp->len == XFRM_MAX_DEPTH) goto drop; ... sp->xvec[sp->len++] = x; xfrm_input() can leave sp->len == XFRM_MAX_DEPTH, and the transport-mode receive path re-enters IPv6 input via xfrm_trans_reinject() with that secpath preserved. If the inner packet carries a destination-options HAO option or a type-2 routing header, xfrm6_input_addr() is called with sp->len == XFRM_MAX_DEPTH; the check (1 + 6 == 6) is false, so sp->xvec[sp->len++] writes one slot past the 6-element xvec[]. The write stays within the sec_path allocation (invisible to KASAN); UBSAN_BOUNDS flags it and panics under panic_on_warn. Use "sp->len >= XFRM_MAX_DEPTH", matching xfrm_input(). This also restores one chain level the old check rejected at sp->len == 5. UBSAN: array-index-out-of-bounds in net/ipv6/xfrm6_input.c:309:10 index 6 is out of range for type 'xfrm_state *[6]'

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: validate ef->size covers the record's name and value When an EA record has a non-zero ef->size, ntfs_read_ea() only checks that the record fits in the remaining buffer (ea_size > bytes), not that ef->size is large enough to hold the record's own name_len + 1 + elength. A crafted image can pass validation with, e.g., ef->size = 24 but elength = 0xffff. ntfs_get_ea() then trusts elength and copies it out of the undersized record, reading past the kmalloc(info->size) allocation and leaking heap memory to userspace via getxattr(): BUG: KASAN: slab-out-of-bounds in ntfs_get_ea (fs/ntfs3/xattr.c:302) Read of size 65535 at addr ffff888100794550 by task exploit __asan_memcpy (mm/kasan/shadow.c:105) ntfs_get_ea (fs/ntfs3/xattr.c:302) ntfs_getxattr (fs/ntfs3/xattr.c:848) __vfs_getxattr (fs/xattr.c:441) vfs_getxattr (fs/xattr.c:474) do_getxattr (fs/xattr.c:800) path_getxattrat (fs/xattr.c:868) do_syscall_64 (arch/x86/entry/syscall_64.c:94) The buggy address is located 80 bytes inside of allocated 84-byte region in cache kmalloc-96 Compute the size the record needs and require ef->size to cover it.

In the Linux kernel, the following vulnerability has been resolved: isofs: fix out-of-bounds page array access on empty zisofs block zisofs_uncompress_block()'s empty-block fast path returns pcount << PAGE_SHIFT, ignoring the incoming poffset, unlike the decompression path which returns bytes produced relative to poffset. zisofs_fill_pages() uses that return to advance its page cursor, so when the zisofs block size is below PAGE_SIZE and a sub-page block leaves poffset partway into a page, a following empty block over-counts and advances pages[] one element past its end, after which "if (poffset && *pages)" reads pages[1] out of bounds. rock.c only rejects a block-size shift > 17, so a crafted "ZF" Rock Ridge record can set it below PAGE_SHIFT; the bug is reached by an ordinary read() of a compressed file on such a mounted ISO9660 image. Return the byte count relative to poffset and zero only [poffset, PAGE_SIZE) of the first page, matching the decompression path. The page-aligned case (poffset == 0) is unaffected. BUG: KASAN: slab-out-of-bounds in zisofs_read_folio (fs/isofs/compress.c:290) Read of size 8 at addr ffff88800f5eac48 by task exploit/142 zisofs_read_folio (fs/isofs/compress.c:290) read_pages (mm/readahead.c:184) ... filemap_read (mm/filemap.c:2814) vfs_read (fs/read_write.c:574) __x64_sys_pread64 (fs/read_write.c:769) do_syscall_64 (arch/x86/entry/syscall_64.c:94) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) The buggy address is located 0 bytes to the right of the allocated 8-byte region in the kmalloc-8 cache

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Handle negative S1 walk levels in VNCR TLB size evaluation Computing the effects of a TLB invalidation involves looking at the size of the mapping cached by the TLB. For S1 mappings such as VNCR, this is deducted from the combination of the base granule size and the mapping level. However, this implies that the S1 MMU is *on*. When the MMU is off, we indicate this with the level being set to a "creative" value of -127 (S1_MMU_DISABLED). This ends-up being misinterpreted by pgshift_level_to_ttl() as it doesn't handle negative levels at all (the level is immediately cast to a u8 and only the bottom two bits considered), leading to an invalidation size of 0. Not helpful. Tidy-up pgshift_level_to_ttl() to handle these negative levels, and ttl_to_size() to always return SZ_1G when no valid TTL is present. This allows the removal of open-coded checks for similar situations. Note that the check for a negative value not explicitely checking for S1_MMU_DISABLED is deliberate, so that actual negative levels introduced with LVA2 and D128 can take the same path if we ever support them.

Apache Airflow FAB provider: changing a user's password through the Admin user-edit PATCH endpoint does not invalidate that user's existing database-backed sessions. An attacker who already holds a copy of the victim's session cookie keeps full access as that user after the password change, so the password reset does not evict them. Affects deployments using the FAB auth manager with database-backed sessions; an administrator (or the user themselves) performing a routine password change is the trigger, and no attacker interaction with the endpoint is needed. This is a second, independent route to the outcome addressed by CVE-2026-82311, which corrected an identifier comparison in the session-invalidation helper. That fix does not repair this endpoint, because the PATCH path never calls the helper at all. Deployments that applied the CVE-2026-82311 fix must also upgrade for this one. Users of apache-airflow-providers-fab are recommended to upgrade to version 3.9.0 or later, which fixes the issue.